qp.defer_measurements

defer_measurements(tape, reduce_postselected=True, allow_postselect=True, num_wires=None)[source]

Quantum function transform that substitutes operations conditioned on measurement outcomes to controlled operations.

This transform uses the deferred measurement principle and applies to qubit-based quantum functions.

Support for mid-circuit measurements is device-dependent. If a device doesn’t support mid-circuit measurements natively, then the QNode will apply this transform.

Note

The transform uses the ctrl() transform to implement operations controlled on mid-circuit measurement outcomes. The set of operations that can be controlled as such depends on the set of operations supported by the chosen device.

Note

Devices that inherit from QubitDevice must be initialized with an additional wire for each mid-circuit measurement after which the measured wire is reused or reset for defer_measurements to transform the quantum tape correctly.

Note

This transform does not change the list of terminal measurements returned by the quantum function.

Note

When applying the transform on a quantum function that contains the Snapshot instruction, state information corresponding to simulating the transformed circuit will be obtained. No post-measurement states are considered.

Warning

state() is not supported with the defer_measurements transform. Additionally, probs(), sample() and counts() can only be used with defer_measurements if wires or an observable are explicitly specified.

Parameters:
  • tape (QNode or QuantumTape or Callable) – a quantum circuit.

  • reduce_postselected (bool) – Whether to use postselection information to reduce the number of operations and control wires in the output tape. Active by default. This is currently ignored if program capture is enabled.

  • allow_postselect (bool) – Whether postselection is allowed. In order to perform postselection with defer_measurements, the device must support the Projector operation. Defaults to True. This is currently ignored if program capture is enabled.

  • num_wires (int) – Optional argument to specify the total number of circuit wires. This is only used if program capture is enabled.

Returns:

The

transformed circuit as described in qp.transform.

Return type:

qnode (QNode) or quantum function (Callable) or tuple[List[QuantumTape], function]

Raises:
  • ValueError – If any measurements with no wires or observable are present

  • ValueError – If using the transform with any device other than default.qubit and postselection is used

Example

Suppose we have a quantum function with mid-circuit measurements and conditional operations:

def qfunc(par):
    qp.RY(0.123, wires=0)
    qp.Hadamard(wires=1)
    m_0 = qp.measure(1)
    qp.cond(m_0, qp.RY)(par, wires=0)
    return qp.expval(qp.Z(0))

The defer_measurements transform allows executing such quantum functions without having to perform mid-circuit measurements:

>>> dev = qp.device('default.qubit', wires=2)
>>> transformed_qfunc = qp.defer_measurements(qfunc)
>>> qnode = qp.QNode(transformed_qfunc, dev)
>>> par = pnp.array(np.pi/2, requires_grad=True)
>>> qnode(par)
tensor(0.434..., requires_grad=True)

We can also differentiate parameters passed to conditional operations:

>>> qp.grad(qnode)(par)
tensor(-0.496... requires_grad=True)

Reusing and resetting measured wires will work as expected with the defer_measurements transform:

dev = qp.device("default.qubit", wires=3)

@qp.qnode(dev)
def func(x, y):
    qp.RY(x, wires=0)
    qp.CNOT(wires=[0, 1])
    m_0 = qp.measure(1, reset=True)

    qp.cond(m_0, qp.RY)(y, wires=0)
    qp.RX(np.pi/4, wires=1)
    return qp.probs(wires=[0, 1])

Executing this QNode:

>>> pars = pnp.array([0.643, 0.246], requires_grad=True)
>>> func(*pars)
tensor([0.769..., 0.132..., 0.0839..., 0.014...], requires_grad=True)

By default, defer_measurements makes use of postselection information of mid-circuit measurements in the circuit in order to reduce the number of controlled operations and control wires. We can explicitly switch this feature off and compare the created circuits with and without this optimization. Consider the following circuit:

@qp.qnode(qp.device("default.qubit"))
def node(x):
    qp.RX(x, 0)
    qp.RX(x, 1)
    qp.RX(x, 2)

    mcm0 = qp.measure(0, postselect=0, reset=False)
    mcm1 = qp.measure(1, postselect=None, reset=True)
    mcm2 = qp.measure(2, postselect=1, reset=False)
    qp.cond(mcm0+mcm1+mcm2==1, qp.RX)(0.5, 3)
    return qp.expval(qp.Z(0) @ qp.Z(3))

Without the optimization, we find three gates controlled on the three measured qubits. They correspond to the combinations of controls that satisfy the condition mcm0+mcm1+mcm2==1.

>>> print(qp.draw(qp.defer_measurements(node, reduce_postselected=False))(0.6))
0: ──RX(0.60)──|0⟩⟨0|─╭●─────────────────────────────────────────────┤ ╭<Z@Z>
1: ──RX(0.60)─────────│──╭●─╭X───────────────────────────────────────┤ │
2: ──RX(0.60)─────────│──│──│───|1⟩⟨1|─╭○────────╭●────────╭○────────┤ │
3: ───────────────────│──│──│──────────├RX(0.50)─├RX(0.50)─├RX(0.50)─┤ ╰<Z@Z>
4: ───────────────────╰X─│──│──────────├○────────├○────────├●────────┤
5: ──────────────────────╰X─╰●─────────╰●────────╰○────────╰○────────┤

If we do not explicitly deactivate the optimization, we obtain a much simpler circuit:

>>> print(qp.draw(qp.defer_measurements(node))(0.6))
0: ──RX(0.60)──|0⟩⟨0|─╭●─────────────────┤ ╭<Z@Z>
1: ──RX(0.60)─────────│──╭●─╭X───────────┤ │
2: ──RX(0.60)─────────│──│──│───|1⟩⟨1|───┤ │
3: ───────────────────│──│──│──╭RX(0.50)─┤ ╰<Z@Z>
4: ───────────────────╰X─│──│──│─────────┤
5: ──────────────────────╰X─╰●─╰○────────┤

There is only one controlled gate with only one control wire.

Contents

Using PennyLane

Release news

Development

API

Internals